This tutorial is set by the author's setting without permission.
The mek fusion pile is extremely powerful, so I will write a tutorial.
------ Fuel production -------
The first is fuel production.There are two kinds of fuels in the fusion pile, [氘] and [氚]
泵: Use the MEK pump plus the filter to upgrade the heavy water, and then the 氘 is used in the electrolytic machine.
把: Use the salt tower to salt the water into salt water, then salt into liquid lithium, and then use the rotor to rotate into a gas, stuff it in the neutron activator into a pupa.
After the reactor is built, use the gas pipeline to input 氘 and 氚.(Don't care about the purple pipes on the right, that is D-T)
------ Reading Dackal ignition -------
Laser should be used for ignition of the reactor, which is this thing.
It will emit laser in front (as for which side is the front, think about the original Pistons), and enter the electricity later.
But this laser energy is not enough, what should I do?Of course, it is stored (don't tell me that you put a pile of laser) (of course, it is not not possible, it is a bit large).
This is used for laser, laser amplifier
But how can I save it?
Because you do not control red stone control
Just adjust it to a high signal
It can be seen that energy is already existed
How to ignite the next?You still need a thing, the black body radiation cavity
At this time, it cannot be used directly, and it has to be infused with D-T fuel. As for how D-T is synthesized, go to the part of the D-T below to see it.
After the black body radiation cavity is placed in the reactor, the laser energy is shot into the reactor.
How to shoot?You must have seen this when you build a reactor,
Just hit it towards it.I suggest that the energy tank of the rookie and other incremental devices be played again, and the 100%ignition is successful.
But someone must have said: How long do I have to wait for this?
So please come out with a new machine: laser traction beam
It allows laser to shoot in front of it (as for which one is the front, the truth is the same as the laser)
Therefore, we can create such a ignition array
This is much better.
At this point, the basic air -cooled reactor is built and ignited.
------ Boiler Water Cool -------
But the amount of air -cooled power is not large, what should I do?
The water -cooled reactor appeared.
The steam system that comes with a fusion heap is too weak, so we need to use a steam boiler.
Use the heat guide cable to guide the steam boiler from the reaction stacking and pass it to the water, and the steam starts to generate
Note that the boiler's water consumption is large, you need a water supply heater with almost unlimited water.I recommend using a high -end hydraulic generator (yes, you read that right, this stuff can output water)
Let's take another industrial turbine and pass the steam, and it starts to generate electricity
----- D-T fuel -------
But despite this, what to do if the power generation is not large enough, use D-T fuel.
D-T fuel is irrigated in the chemical irrigation machine
After the irrigation, input the reactor with the gas pipeline, the reactor will produce more heat and send more electricity.
Note that the D-T fuel will be consumed at the moment of the input reactor, so you have to add a gas storage tank in front of the pipeline that directly input and the pipeline to prevent all use D-T fuel, just like this as this is like this, it is like this.
At this time, your reactor has entered the state of the highest power. If you want to continue to increase power, you must increase the fuel output.
------ automated reactor --------
The black body radiation cavity can be done in the factory, and the D-T unit is automatically installed in the figure below
The left pipe is an input tube, and the empty radiation cavity enters the storage tank from here. The upper pipe is an output tube. The full radiation cavity is output from here.
The input and output configuration of the gas storage tank is as follows
The gas storage tank is not automatically input and output, and the pipeline needs to be pulled out.The corresponding grid color is blue, so the input and output tube should be connected to the blue surface.
Laser output automation:
First of all, you need to press the button in the lower left corner of the laser amplifier to look like the figure below, so that you can read the internal energy level with redstone comparators.
When reaching a certain energy level, you can output
But what if there is no radiation cavity in the reactor when the laser is shot?Just test whether there is no.
But the GUI of the reactor cannot be detected. What should I do?Then check the radiation cache area?
The resonant storage box in the figure is used to caching the black body radiation cavity. The redstone comparator checks whether there is a black body radiation cavity available. As long as there is a black body radiation cavity in it, there are absolutely there is also the reactor. This non -door+reduction deviceIt is so that the laser will not be output without a black body radiation cavity
Note that the black body radiation cavity must input the reactor controller from the reactor interface (1.16 miles of black body radiation cavity is not an port input, it is input from the shell)
The production of the ignition device is complete, what about the black body radiation cavity production unit?
Black body radiation cavity:
We cannot use metallurgical pouring machines. We need to use the pouring factory.
Tip: The grid corresponding to purple is actually something that needs to be melted in the irrigation
The black body radiation cavity produced is used as mentioned above for fuel loading
After filling, automatically output to the radiation cache area mentioned above.
In this way, the automatic ignition of the reactor can be achieved. If you are afraid of insufficient fuel, then put a reactor logic adapter and set the mode to the mode referred to by my mouse. Coupled with the structure of the non -door+door and the door structureEssenceFinally, give you a panoramic map of an automated reactor
If you do n’t understand anything, please tell me in the comment area that I will answer it. If you have any suggestions for this article (especially the automated reactor part), you are welcome to make this tutorial.