This tutorial is set by the author's setting without permission.

In addition to the crystal device, the core of the five -time line is on the sulfuric acid to ensure that the supply of sufficient supply of sulfuric acid (mainly sulfur dioxide) is the prerequisite for the five -time line to run at full speed.Here is an idea of ​​using thermal+IC2 to achieve fully automated sulfuric acid.Simple and easy to go.

Module you need to use:

· General Machinery

· Pressure pipeline (provides unlimited water sources)

· Industrial Age 2 (the core of gunpowder sulfur powder)

· Heat expansion 5 (the core source of gunpowder)

The basic thinking is as follows:

Thermal stones are made of sand and gravel → purify warehouse treatment into vermiculite → crusher treats it into gunpowder → IC2 extract machine extract sulfur powder → send it to the chemical oxidation machine. The subsequent process can refer to the other five times line to build tutorials.

Not much to say nonsense, start to build.

First, put on the stone -making machine in the heat expansion. It is recommended to upgrade to the resonant level, so that 4 upgrade modules can be installed.Professional upgrades choose debris deposition, and the remaining three upgrades selection auxiliary receiving coils to ensure that the machine operates at full speed.(Energy supply must keep up)

The configuration of the stone machine is shown below:

Without adding other modules, the stone manufacturing machine that is installed with debris deposits is default. If other modules are installed, turn the arrow below by yourself.

The stonemaker requires water and magma to work. The formula for producing gravel is 0MB (left groove) and 1500MB (right groove).Although the lava is 0MB, you still have to manually get some lava in and let the liquid groove on the left identify as lava instead of "empty", and do not consume lava during actual work.The water extraction of water uses the unlimited water source block of the pressure pipeline. Use MEK's ultimate mechanical pipeline to place it directly on the water source block. If the adjustment device is changed to the connection, it is directly supplied by unlimited water.(Figure below)

Because this is the water entered from the left, you must configure the side options of the stone machine.Open the GUI of the stone machine, click the small gear, and press the side of the liquid to enter the small black square on the side of the liquid:

Then add a bucket of lava and let the stone maker start to work:

At this time, the stone creation machine is already a permanent motivation, and the lava will not be consumed.Next, the gravel built out of the unintelligible gravel was pumped into the purification warehouse of MEK, and it was treated as a vermiculite, and then the vermiculite was guided from the purification warehouse to send it into the crusher. After the construction was completed, it should be like this:

When the logistics pipe exports the gravel from the stonemaker, use the adjustment to adjust the connector to draw out the mode to pull out the gravel.The next step is to process the treated gunpowder into sulfur.According to MEK's processing method, the chemical firing room needs to be treated with gunpowder to obtain sulfur, but this requires consumption of hydrogen chloride. Because the four -fry line itself depends on hydrogen chloride, the five -twice line is built on the basis of four times line. ThereforeIt may also need to make additional distillers to ensure the supply on both sides, which is more troublesome.So we chose the IC2 extract machine and extract sulfur powder directly from the gunpowder.In order to allow the extract machine to run at full speed, we need to create a extract machine array, which requires 8 units, and then each one adds 11 overclocking upgrades to ensure that it can keep up with the speed of the MEK factory machine.

PS: If you do not turn off the voltage overload explosion mechanism of IC2, you have to install a high voltage upgrade to the extractor. Here I have turned off this mechanism for convenience.

Then it is created. The logistics pipeline on the back of the unit is drawn out of the interface settings, the sulfur powder is drawn, and the chemical oxide machine is divided into sulfur dioxide.

The subsequent operations are exactly the same as the operation of the ordinary five -time line. The sulfur dioxide and oxygen are irrigated into sulfur dioxide, and then sulfuric acid is treated to send it into the chemical dissolving room.However, when you irrigate the sulfuric acid, you need to use a rotary gas -liquid converter to treat the water as a water vapor. This can also imitate the water supply of the stone machine, and it can be connected directly with the infinite water source block and the mechanical pipeline.open.

This sulfur dioxide production line can be regarded as easy to build, and it looks very simple.In addition, the previous replacement of the unit (stone creation unit, purifying warehouse unit, and crushing machine crew) can ensure the stability of subsequent sulfuric acid production. The products in front are basically spare -surplus. Do not worry about the headache of the dissolved room units insufficient sulfuric acid.