This tutorial is set by the author to use the CC by-NC protocol.
The main content of this tutorial is the introduction of the relay in the laser, and how to use them to build an automated charging platform.
Item laser relayr
Many automation systems need to automatically move items from one place to another. The common items transmission method is to use pipelines and some send/receiving equipment.The advantage of items laser relayrs is wireless transmission, and it can have extremely fast speeds when sending/receiving support, but its configuration is slightly more complicated than traditional pipelines.
Moderate item transmission network
Using multiple items laser relatives to connect different containers or equipment with internal containers can form an item transmission network.However, the laser relayr itself does not actively enter the output item. In order to access the items from the network, it is necessary to have an object transmission interface.
Item transmission interface
Use funnel and item transmission interface interaction
Connect an item transmission interface with the laser relayr to the network, you can use it to obtain all the items and access space in the network through it, and you can use funnel, pipelines or other equipment to interact withCan be used for interaction.
After the construction of an item transmission network is completed, the items will be transported automatically.In the automation system, in order to enter the specified item into the specified container, high -end items laser relayrs need to be needed.
High -level item laser relayr
GUI of senior items laser relayrs
The high -end item laser relay has a GUI interface, which is divided into two parts: left and right. The left side indicates that the items enter the network through the relayr's entry into the network.Set the white list/blacklist input and output, and whether to match the metadata, NBT data, mineral dictionary and module.
There is also a S button below. When the high -end item laser relayr is close to a container, press this button to quickly add the items in the container to the white/blacklist.
Just as a wireless relayer
Note that the configuration only acts on the container (or item transmission interface) connected to the laser recurator of the advanced item, so if there is a high -end item laser relative in the network, then the white/blacklist is configured with its white/blacklist not.Any impact on item network transmission.
Charging platform automation
Charging table structure
In the charging table structure, the item display platform and the charging table have a grid internal storage space, which can be input/output through the laser enabler.Note that when the laser relayr is placed on the item display table, you must press and hold the sneaking key, otherwise it will be placed in Taichung.In addition, you need to enter energy (energy laser relayrs) to the four items display desks.
Configuration of high -level items laser relayrs
On the item display desk, the entry configuration should be a white list corresponding to the consumption item.And stay there until the completion of the filling process is consumed, and then the next item can continue to enter.
On the charging table, the entry configuration should be the whitelist of the corresponding charging items. The outlet configuration is a blacklist of the same items. The reason is the same as above.However, the filter table itself has a similar filtering function, so in fact, you only need to set the input/output to the black list of empty, or it is also possible to use ordinary items laser relayr.
Input/output part
Place an item transmission interface in a suitable place. A funnel is used to enter the material that consumes. Note that this funnel should not connect to the external container, otherwise it will stuck the items.The finished items (can be output to the external container) and put the item laser relayr.
Note that the outlet is configured to the white list of items that can be used to complete the items, otherwise the input material will be leaked directly to the output (you may need to complete the item that can be completed once to obtain it.The list, but this will take up the grid).You can also put a lever next to the funnel, so that you can stop and start the workflow at any time.
Full picture
Finally, connect the relay with a relay wrench. At this point, a simple automation charging platform is completed.
Remark
Because the original funnel has a cooling time, it will cause stuck when entering a variety of items, so it is recommended to use pipes or other logistics equipment to enter items.
There is also a variant of a funnel -type item transmission interface. It is essentially a two -in -one block of a funnel and item transmission interface. There is also a problem of transmission stuck.Because the original funnel still has 5 storage space, it can basically replace the box), it is not recommended to use it.
The item laser relayr can also use the compass to set priority, and the items will always try to enter the highest priority container. If the container is full, it will try to enter the next high -priority container.However, I am not very clear about the law of the items when the priority is the same, and the white/blacklist of the high -end items laser relayr is completely sufficient, so I do n’t introduce too much.
