Saving
The machine work requires uninterrupted input energy, so only one -to -one or more energy supply can be provided, and one -to -one more energy is available.Unless your processing time only needs 1Tick
The machine has the energy input range (voltage, speed, etc.), and only accepts energy input within the range (special circumstances: tandem voltage, atmospheric heat source); when supplying more energy, the total power acceptance is the upper limit of the machine energy, and at most [upper limit, the upper limit is required/Lower limit] Taibara motivation or current, for small machines, the largest number is 4.
When the formula consumption is lower than the lower limit of the machine's energy, the overclocking punishment will be triggered, that is, it consumes four times the energy to obtain twice the processing speed.As we all know, this is a GT tradition.The machine description has [can be overclocking when consuming extra energy], and there is no overclocking punishment. They are: liquefied furnaces, dryers, distillation rooms, material replication machines, material manufacturing machines and all large machines.
Machines equipped with switch covering boards are no longer consumed when shutting down, and tried to turn off their adjacent energy supply machines.Only one -to -one energy supply can be closed.If one more, or involving multiple energy transformations, you should use the sensor+red stone machine switch to turn off.Recommended use: Activity sensor (ready), energy sensor (reverse phase)
Electric transduction machines (electric motors, laser, electromagnets, etc., except for electric engines) can be used to adjust the power with the selectioner coverage board.
Machine energy supply mechanism
Check the machine entry, each machine has a rated power.However, it should be noted that the rated power is just a tradition. In GT6, the energy input range of the machine is more useful.
Machine material bronze (T1) steel (T2) titanium (T3) tungsten steel (T4) rated power 32 (LV) 128 (MV) 512 (HV) 2048 (EV) Energy range 16 to 6464 to 256256 to 10241024 TO 4096
There are several meanings in this range:
The size of the single -stock energy flow (such as voltage, torque, etc.) that the machine can accept is too low or too high.
Maximum power of the machine.
The scope of the original speed processing formula of the machine.
Excessive EU voltage can enter the machine normally after loss in the wire.Candid resistance cults, grind 88EU/T to 64EU/T with 12 wires, and from time to time, call a passing Internet addiction boy.
Excessive HU and CUs will not cause the machine to stop, and the energy that exceeds the upper limit will be wasted.
The maximum power/minimum power is the maximum current that the machine can accept. The small machine is 4A; the transformer, the gearbox, etc. are the minimum value of the maximum/low voltage of the high -level voltage, that is, the maximum 16A current can be accepted when the transformer is up voltage.
Formula machining power, energy power, machine energy range, machine material, and processing speed of processing constitute the main line of GT6 technology line.
Pressure -supercharging mechanism
In the same machine, the total processing speed is proportional to the power, that is, the maximum power is 4 times faster than the minimum power.
When the formula is higher than the range of the machine or the power input of the machine, the formula is not recognized and will not enter processing.Okay ~ I can't handle the material if I can't handle it
When the recipe power is lower than the machine range, the formula will become overclocking formula: production quantity X2, energy consumption and power X4.The formula after overclocking is still not within the range of the machine, and continues overclocking.
Formulas (such as centrifugal magma, 64RU/T) at the same range of border areas are the same as the same energy in the two machines.
The supercorporating superclocking mechanism is not a reward but a punishment.So the rewards are rewarded.
It can be seen in the figure: After starting at the same time, the furnace processing speed with a melting furnace of 16 ~ 64 is 1 ~ 4, 64 ~ 256, respectively.The furnace processing speed is 8, 16
※ The energy input is 4096 melting furnace. The logistics speed limits the processing speed of the machine, resulting in the processing speed of only 16.This melting furnace is actually a special case. In addition, only the polytable coil can achieve super tick processing
This has been avoided as much as possible in the game, and the machine will perform parallel processing to extend the total time of a single production, such as "(up to 8X Processed Per Run".
The reduction of the pressure overclocking itself is reduced, and only the machine does not change the energy to reduce the processing speed (X0.5).It is unwise to use high -level machines in the early and middle period of energy tension.However, the formula after overclocking can speed up (X4) in the advanced machine (X4), which is doubled before the overclocking.Two times the recipe of energy processing is here.Therefore, the lower the machine, the higher the energy utilization efficiency, the higher the machine, and the faster the production speed.Small machines can also win with quantity. The two 64RU bronze rolling machines are twice as faster than a 128RU rolling machine. 4096RU for a bronze rolling machine array is 16 times faster than a tungsten steel coil machine alone.
Large machine overclocking
The predecessor of large machines is to handle arrays, which is equivalent to concentrating multiple small machines in a multi -block structure, so it can be unattended.That is, there is no need to provide additional energy to improve the formation level during overclocking. How many times the input energy is to increase the processing speed, but pay attention to the large -scale machine's own energy loss and reduce the processing speed (50%, 25%).The advantage of large machines is that the high magnification is not damaged overclocking. As the formula level increases, the upgrade space of small machines decreases, and the advantages of the array decrease.When facing the highest level formula (1024Gu/T and above), the large machine has lost the advantage of parallel treatment. At the same time, due to its own loss, even the speed is not as good as the corresponding tungsten steel machine.It's your large centrifugal machine.Cross -voltage RU merger
Players may notice when steelmaking: a rotating power engine can accept the energy of up to 4 turbine.Ordinary machines usually have only one face -to -face supply, but they can also use universal relay or adjustable gearbox (gear box) to achieve four bands. This is a good choice for players who need to process 256RU/T formula in the early stage but need to process 256RU/T formula.EssenceHowever, the four strokes are the limits of the machine. The adjustable transmission can not only achieve two bands, one, three bands, and four bands. When eating with the gearbox, the sixteen belt is not a problem.Mechanical crickets 16 steel internal combustion engines are as high as 1024RU, and even if you can't handle 铱, you can also bring titanium machines.
※ In the figure, the steel internal combustion engine is 64RU/T, and the gearbox is a boost mode.
