This tutorial is set by the author's setting without permission.
The inferior is one of the most basic machines in AE2, but the automation of the inferior has always been more troublesome.
There are also many tutorials for automated compressors on the Internet, but they are all designed.Isn't it unavailable :)
This tutorial will teach you to set up an automatic pressing device for three -threaded parallel work through the sub -network.The characteristic is small and efficient.Pretty good
Note 1: The character in the tutorial is very important. You must follow the tutorial, otherwise the orientation of the printer will affect the output and input of the items.
Note 2: If you like to learn through video, click here.
First you have to prepare the materials:
ME input bus: 9
ME storage bus: 18
ME interface: 4
ME cable: 15+ smart cables at night thieves look good
Quartz fiber: 6
Printing device: 9
Select a surface connecting the main network, and the bottom surface is selected here.
First put some squares at the bottom, and then put on the ME interface. This ME interface is used to communicate with the main network.
Put a block on the ME interface and put it on a printed device. Note that you must face the side and jump up and put it down.
Put a press on each side of the square on the left and right sides above the ME interface. Note that you must go to the side and put it on the front of the ME interface.
Knock the square above the ME interface and put the input bus on the back of the three printers.
Put a storage bus above the ME interface and connect it with the ME cable.Mom 1.16.1 opened the ME interface and actually collapsed
Put the quartz fiber before and after the ME cable to isolate and provide energy.In fact, it is a sub -network with only output
Put a block in front of the ME interface, and then put a compressor on each side of the left and right sides of this block. Be careful to go to the side and put it on the front of the square.
Put a block in the back of the ME interface, and then put a compressor on each side of the left and right sides of this block. Be careful to go to the side and put it on the front of the square.After putting it, use the handle to the front to let it press the side of the print.
Remove all the auxiliary blocks and return to the front.
Put a square on the top of the top, and then put a press on the right, and walk to the side and put it on the front of the square.
Put a ME interface on the left side of the block.
Put a press on the quartz fiber behind, be sure to put it in the quartz fiber.
Put a ME interface on the printed printed.
Congratulations here, you have completed half of the tutorial, and you only need to connect these printeds to work.
Back to the front, convert the remaining ME interface to the ME interface panel, and then press the front of Shift in the ME interface at the bottom.
Put the storage bus in the red circle position in the red circle of the picture.
Open the storage bus of the three main pressure printers in the middle, which is marked as only redstone input.
Open the auxiliary printer on the left side of the bottom and put it in the printed template, and then open the storage bus next to it. It is marked as a diamond input.
Open the auxiliary printer on the right side of the bottom and put it in the computing pressure template, and then open the stored bus next to it. It is marked as a high -pure Setz quartz crystal input.
Open the auxiliary printer on the top and right, put it in the silicon press template, and then put an input bus on the left.
Put a quartz fiber isolate and provide energy below the ME interface on the left.That's right, this is also a sub -network
Finally, connect with the ME cable and the front is completed.
Go to the left side, placing a quartz fiber facing the ME interface at the bottom, putting an input bus on the right auxiliary printer on the right, putting a storage bus under the main pressure printer in the middle, and finally using ME to use Me.The cable is connected.Another sub -network
Going to the right side, placing a quartz fiber facing the ME interface at the bottom, putting an input bus on the auxiliary printer on the left, putting a storage bus under the main pressure printer in the middle, and finally using Me.The cable is connected.One more sub -network
When you walk to the back, put a quartz fiber facing the ME interface at the bottom, then put a storage bus on the left and right, and finally connect it with the ME cable.The last sub -network
Jump to the top first, facing the side of its own (the press on the left is the press and the ME interface on the right).
First handle the right, press Shift in the red circle position of the picture, put on the storage bus, and mark it as a silicon -only input.
Go to the left position and press Shift in the red circle of the picture and put the storage bus.
The No. 1 storage bus is marked as silicon -only input.
The No. 2 storage bus is marked as a logical circuit board input.
The No. 3 storage bus is marked as a silicon plate input.
Back to the back, open the middle press in the middle, put the silicon pressure printing template, then put a storage bus on the left side, and mark it as silicon input.
Open the printer in the lower left in front of the back, put it in the logic pressing template, then put a input bus above it, and then mark the storage bus on the right side to only input to the gold ingot.Open the printer at the bottom right behind, put the silicon pressure printing template, then put a input bus above it, and then mark the storage bus on the right side of the silicon -only input.
Next, put a input bus on the right side of the press on the middle of the posterior rear, put a storage bus on the right side of the ME interface above the posterior posterior, and finally use the ME cable to connect.Don't think so, there is another sub -network here
Back to the front, put three silicon and three red stones in the only interface panel.Hey, lubricating oil
Finally, hold a line under the ME interface at the bottom to the main network.
Sample production needs to use the processing mode, and then only need to mark the corresponding materials and the corresponding output.
Make the models need to be placed in the ME interface connected to the main network.
Then you can use it.
If you want faster speeds, you need to put a acceleration card for all printers.
Note that except the three input bus in the middle, other input bus cannot be accelerated, otherwise there will be some inexplicable problems.
