1. Foreword
Through this chapter, you will learn the composition of the industrial grid and the usage of some basic power machines.
2. Wire and grid
The core of the industry is electricity (energy unit: EU). Through the previous introduction, you can easily process tin, copper, and gold -made wires with [Forging Hammer] and [Cut the Wiring Piece], and then use them to build a grid (Right -click and place left -click).
Tin -made wire: 1 ingot = 3 wire, 0.2eu per grid, suitable for low voltage (0 ~ 32V) power grid. Because the loss algorithm is for the house, it is not used between [Power Supply] and [Electrical Electric]4 (0.2x4 = 0.8 <1) or above, there is no loss
Copper wire: 1 ingot = 2 wires, 0.2eu per grid, suitable for low, medium pressure (0 ~ 128V) grid.If you are transported by the medium voltage, it is recommended to use rubber insulation to avoid electric shock.
Gold -made wire: 1 ingot = 4 lines, each loss of 0.4eu, suitable for low, medium and high voltage (0 ~ 512V) power grid.If the medium/high -voltage electricity is transported, use rubber insulation.
3. Entry -level generator- [Fire Director]
Without electricity, it is always a big problem, but before power generation, it is best to come to some charging batteries (capacity: 10000EU).
Thermal generator is the most basic power generation equipment. Other senior generators are also based on its synthesis. You can use [Iron Furnace] or [Floor] for synthesis.
Right -click the interface (GUI) of the thermal generator, the lattice (coal/charcoal, other combustibles, but excluding magma barrels) below, the power generation speed = 10eu/t (that is, 200EU/second), each firepower)The generator comes with the 4000EU power cache, which is exactly equal to the power generation of a coal/charcoal.Put the [Charging Battery] above the grid, you can charge it.
Note: All industrial machines must use [wrench] right button to disassemble instead of the left.
4. Extractor
Industry 2, individual recommendation is to produce a extract machine first to improve the yield of [rubber].
Extract machine consumes power = 2eu/t, process items once in 13 seconds, and consumes 520EU.
——PS: How to power the machine?① Use the wire to connect to the generator and use electrical appliances. ② Use the battery to power the machine directly.
5. Powder
[Minerals] Double output. Although there are many MODs, it is still the most classic of Industry 2.
Click the progress bar in the middle of the machine interface, you can [Display Formula], the powdery speed of the powder consumption = 2eu/t, processing items once in 15 seconds, and power consumption of 600eu.
After having the powder, the [copper ore] and [tin ore] are used for powder, then synthesized [bronze powder], and finally fired [bronze ingot].
Note: With bronze ingots, please give priority to [wrench].Right -click on any face of the machine to turn the front of the machine. If it is positive, remove the machine (non -destructive); shift+right button = reverse.
6, electric furnace
[Iron Furnace] Upgrade again, get rid of the troubles of careful calculation.
The processing formula is the same as the furnace, but it is faster and more fuel.Power consumption speed = 3eu/t, process once every 5 seconds, and power consumption 300eu (you read it right, a coal can burn 13.3 items).
7. Compressor
Perhaps it is useless for the time being, and some big brothers are directly used to press [Industrial Diamond].
Power consumption speed = 2eu/t, process items once in 15 seconds, and consume 600EU.
8. Electric storage tank (capacity: 40000EU, caching 10 coal combustion power generation)
The cache of the fire generator itself is too small, and it is easy to waste coal. At this time, adding a [power storage box] next to it is a good way.The dot is [output surface], the wires are powered from here, and the rest are [input surface].
9. End
