This tutorial is from MC Encyclopedia (MCMOD.CN) using the CC By-NC-SA protocol.
1. List of multi -block structure
GT5 adds a large number of multi -block structures, and many of them must be completed in your GT career.
For detailed information about each multi -square machine, please go to their respective entries to check.
Charcoal pile (only 5.09)
The only purpose is to make charcoal.
In the default environment of non -official 5.09, if there are no other mods, this will be the only way to get charcoal in the early days.Generally speaking, it is also necessary.
Soil high furnace
The biggest purpose is to burn steel.In addition, some mixed minerals can be smelted to increase production.
If there are no other mods, the dirt blast furnace must be done in the early stage.You can choose to make a bronze blast furnace or refractory brick blast furnace according to your own resource reserves; but in any case, this will be the biggest threshold for you to enter the power era.
Industrial blast furnace
It is used to burn a variety of metals and alloys, as well as smelting some minerals.Emphasized machines that penetrate the entire science and technology line from the middle of the period.
Vacuum freezer
Commonly known as large refrigerator.It is also necessary in the technology line.
Some senior metals/alloys are burned out of the blast furnace, which is in a hot ingot state and cannot be used directly. At this time, the vacuum frozen device needs to be cooled to cool it.
In addition, a large amount of cooling unit stored in the nuclear reactor can cool through the vacuum freezer to achieve a strong cooling effect and exchange for strong output.This nuclear power scheme is commonly known as strong cold.
Agglomeration compressor
It is used to make a lottery board, or compress the gem powder into gems.After the high version, you can condense low gems into high -end goods. It can be used to make up for the exquisite gemstone required to obtain the lens in the sieve filter.
Distillation tower (only GT5.08 above)
Refine crude oil distillation into a large number of useful products.I don't know where to go than a single distillery room.
In addition, you can distille the IC biogas cult convention for biomass biogas at a crazy speed
5.09 Core machine in Sinopec Industry, it is recommended to produce at least one units -compared with the distilled tower, the distillery room that can only produce one product can be very urgent.
Crack (only 5.09)
Crack the weight of the weight, and then distille it again.
Non -essential machines can be increased in the petrochemical industry.This work can also be done, but the product is only 80% of the products
In 5.09.32, the formula of the chemical reaction kettle cracking oil is canceled, and you can only use this machine to crack oil.
Thermal resolution furnace (only 5.09)
The heat of the log was solved as charcoal, the sugar thermal thermal was used to charcoal powder and water (what's the use), heated the bran and water to the IC biomass/fermented biomass, and the speed was very fast and saved by electricity than the mixer.Essential machine for biogas cults
Non -necessary machines.To some extent, it is a high -end charcoal pile that can automate and efficiency.However, there is a recipe that solves the heavy oil of log heat, making the renewable of various petrochemical products possible.
After the chemical update of 5.09.31, the by -production when firing charcoal can be used as an important chemical raw material.
Industrial melting
Burn a large amount of items at a time.
Why not make a try?It can also consume the coils of retirement of blast furnaces.
Treatment array (only 5.08 or more)
It can be processed in batches of up to 16 formulas of unilateral block machines.
Comes with ultra -net room environment.
The grinding machine can produce all the by -products regardless of voltage.
Although the cost is expensive, it can avoid the troubles of a large number of unilateral machine wiring -maybe it can reduce the stutter at the same time.It is strongly recommended to use the processing array when performing large -scale production.
Equipment line (only 5.09)
It is used to make machine parts above LUV.
Essential machine.In 5.09, quantum sleeves, fusion hosts and other things must be assembled through the assembly line.
Gathering pile (only 5.08 or more)
Plasma plasma is generated to power generation, or some terminal metals are transformed.
Obviously it is a necessary machine for customs clearance.
Petroleum drill (only 5.09)
The only way to collect GT oil fields.
Recommend at least one, especially when there is no oil provided by MODs such as BC -you can't always expect oil sand to meet your petrochemical industry.
Mining (only 5.09)
Automatic mining+crushing+yield.
Collect a good helper for GT ore veins.Strongly recommended.
Ultra -Jing Room (only 5.09)
From HV, the multi -square structure necessary for production of high -end circuit boards.
Large boiler
Production of steam efficiently.With large turbines, it can efficient real estate capacity.
Large hot switch (only 5.08 or more)
Cooling magma/thermal coolant, and producing steam/overheating steam at the same time.
Enhanced version of IC heat exchanger.It is also a good production capacity.
Large turbine (only 5.08 or more)
One of the important power generation equipment in the middle and late stages of GT is divided into four types:
Large steam turbine: use steam power generation and return distilled water.
Large gas turbine: combustion and flammable gas power generation.
Large -scale overheated steam turbine: Use overheated steam to power generation and return steam.This means that you have to use large -scale plasma turbine with large steam turbine: consume plasma power generation and return the corresponding cooling fluid.
For details of the operating mechanism, please refer to the specific entry.
Large diesel engine (only 5.09)
One of the important power generation equipment in the middle and late stages of GT is burning combustible liquid fuel power generation.
For details of the operating mechanism, please refer to the specific entry.
Concrete backfill (only 5.09)
Fill the underground cave with concrete.
It can be used to auxiliary manufacturing brush towers, or reduce rendering pressure, and provide FPS.
Advanced processing array (only 5.09.32pre6)
The upgraded version of the array is more expensive, which is equivalent to 64 unilateral machines working at the same time, which eliminates the trouble of wiring.Other characteristics and processing arrays are the same.
Although it is expensive, it is practical!
Second, detailed mechanism
1. The role of each warehouse
· Enter the bus
Provide machine raw materials for machines.The ULV -level input bus has a capacity of 1 grid, LV has 4 square meters, MV has 9 square meters, and HV and above have 16 blocks.Therefore, unless special requirements are required, there is no need to use too high -level input bus.
Can only be automatically input from the front.
It can be shared by multiple multi -block structures to provide them with raw materials at the same time.
· Output bus
Accept the product of the machine.The capacity is also input bus.Similarly, unless special requirements are required, there is no need to use too high -level output bus.
It can only be automatically output from the front.
Unlike unilateral block machines, the machine will not stop working after the output bus is filled, and the excess products will be directly destroyed -so please take the items in the output bus in time.
Can be shared by multiple multi -block structures and receive their products at the same time.
· Enter the warehouse
Provide fluid raw materials for machines.The fluid cache is 8000*(grade +1) MB.
Any surface of the output warehouse can be input/output fluid, so it can be replaced to some extent when the pump module is covered with the coverage version.But items (such as fluid units) can only be input/output from the front.
It can be shared by multiple multi -block structures to provide them with raw materials at the same time.
· Output warehouse
Accept the fluid product of the machine.The fluid cache is 8000*(grade +1) MB.
Similar to the output bus, the machine will continue to run after the fluid in the output warehouse is filled, and the excess fluid will directly lose.
The output warehouse can automatically output fluids from the front, or output fluids such as pump modules from other planes, but cannot automatically input the fluid; and it can only be automatically input/output items from the front.
Can be shared by multiple multi -block structures and receive their products at the same time.
· Energy Warehouse
Provide energy for the machine.
You can accept the current of 2A at the corresponding level.
Can be shared by multiple multi -block structures, and at the same time provide energy to them -as long as confirming that your power supply can meet their needs.
· Power Warehouse
Accept the power generated by the machine and output at a current of 1A.
Well, it seems that no multi -square block can use the power warehouse from the structure ...
· Elimination warehouse
When the sound warehouse is placed in a multi -square machine, the side of its black pores must be facing the outside of the machine, and the direction of its orientation must be air. In GT5.09, between the power machine, all need to eliminate it.The machines of the sound warehouse are all polluted during runtime.Therefore, although this block has always been called the sound -disappearing warehouse, from the perspective of its setting, it is better to be called a sewage warehouse.
In addition, high -level sound -discharging warehouses can reduce the discharge of pollution.From 5.09.31, blast furnaces will be able to recover the exhaust gas (carbon dioxide, sulfur dioxide, carbon monoxide, etc.) generated during smelting mineral smelting, and further be used as raw materials for other chemical formulas. The level of the sound warehouse will also determine the recovery ratio of exhaust gas.
Grade pollution level of exhaust gas recycling ratio
LV
100%
5%MV70%35%HV48%57%EV34%
71%IV24%81%LUV16%89%ZPM11%
94%UV8%97%Max5%100%
In other words, a blast furnace that uses an LV sound warehouse will pollute at a rate of 100/s; but the pollution will be reduced to 5/s after using the MAX sound -disappearing warehouse.
· Maintenance warehouse
Used to maintain the machine.
When the maintenance warehouse is shared by multiple machines, it can only repair a specific machine.Therefore, it is not recommended to share the maintenance warehouse.
· Automatic maintenance warehouse
During the operation of the machine, if a new failure is generated, the automatic maintenance warehouse will consume 4 aviation tape, 4 steel screws, 2 lubricants units, and 2 advanced circuit boards (the processor cluster/nano -processor universal)To repair.Similarly, it is not recommended to share automatic maintenance warehouses.
2. Power consumption of multi -square machine
For the multi -square machine of GT5, the electric energy they consume is provided by the energy warehouse; therefore, roughly, the voltage level of multi -square machines determines the voltage level of the energy warehouse; when processing the formula, these machines will also beSurgery in accordance with the same rules as basic machines.
Taking the blast furnace as an example, when using a MV energy warehouse, its voltage level is MV; the formula of the aluminum powder requires 120EU/T power, which takes 85s. It is a MV -level formula, which can just be processed by such a blast furnace.If you use 1 HV energy warehouse, the voltage level is HV, which is 1 level than the formula of aluminum powder. Therefore, the formula will be overclocking once, the power will rise to 480EU/T, and the time will drop to 42.5s.However, the above situations are limited to the case where only one energy warehouse is used.If the multi -block machine uses multiple energy warehouses, its voltage level should be calculated like this: add up the voltage of all energy warehouses to get the input voltage of the machine; the voltage level where the input voltage is located is the voltage level of the machine.
Still taking blast furnace as an example.When using 1 MV energy warehouse+1 ULV energy compartment, the voltage of these two energy warehouses is 128V and 8V, respectively, and the input voltage of the blast furnace is 136V;Level has become HV.However, the input current of each energy compartment is only 2A, that is, the maximum power of this blast furnace is 136V*2a = 272eu/T; if it is used to burn aluminum powder, the voltage level HV of the blast furnace is higher than the level MV of the formula.This formula will still be overclocking, which requires 480EU/T power -in this way, this blast furnace will not be able to handle this formula (in fact, this blast furnace can hardly do nothing).
If the multi -block machine allows existence and there are indeed 5 energy warehouses with the same voltage, the machine will automatically overclock the two voltage levels. The principle is the same as before.
This is also the principle of multiple LV energy warehouses when the blast furnace is in low pressure rises.When using 2 LV energy warehouses, the input voltage of the blast furnace is 32V*2 = 64V, which belongs to the MV; the current of each energy compartment 2A, so the maximum power of the blast furnace is 64V*2a = 128eu/T.Formula.
It should be noted that one of all multi -block machines does not conform to the above rules, that is, the polytable pile -the specific power consumption mechanism is to see the entry for details.
3. Failure of multi -square machine
Most of the multi -square machines of GT5 need to maintain the failure of the machine to repair the machine.These faults will appear in the GUI interface of the machine controller.There are six faults that can be repaired by the maintenance warehouse:
Fault ** Repair Tool PIPE is Loose.Burned out.
*There is no electric iron in the official version of 5.07.07.It is necessary to charge it during use, and there is a rod/exquisite cable made of lead/tin/solder in the backpack as a solder.
** Of course, the aviation tape using GT can be repaired all at one time -but it requires at least MV to make it.
Right -click the repair tool in the grid in the maintenance warehouse GUI to repair it.If these 6 failures are not completely repaired, it will reduce the efficiency of the machine, 10%each.
Still taking blast furnace as an example.When it did not fix "Circuitry Burned Out." This failure, its efficiency will be reduced to 90%, and the power of 120EU/T that originally required for aluminum powder will rise to 133EU/T — except for more power consumption, 2 are 2, 2The energy warehouse will not be able to support the consumption of this formula.Therefore, in the official 5.07.07 version, when the initial enhancement, if the sapphire powder is not used to obtain aluminum, we need to add another LV energy warehouse to the blast furnace.At this time, the input voltage of the blast furnace is 32V*3 = 96V, which is still the MV, which will not make the MV -level aluminum powder formula overclocking;Essence
It should be noted that the probability of 1/6000 per 50s during the operation of the machine runs one of the above failures, so it is recommended to maintain it regularly.
In addition to these 6 faults, there are some other faults:
Failure meaning repair method Remarks inComplete Structure. Check whether the multi -block structure is complete and whether the material is correct.The machine will immediately stop processing and return to the shutdown state.Putting the mining pipe in the input bus of the corresponding machine is also effective Missing Turbine Rotor. Large turbine lacks turbine to add turbine to the stealth grid at the top right of the controller.-
In addition, there are some hidden failures:
Inlet/exhaust block.All machines that use the sound of sound warehouses must be air for the squares of their sound warehouse; the front of large turbines and large diesel engines is their intake port. These nine squares must also be air squares.When such a failure occurs, the machine will stop processing the next moment after the soft hammer is forced to restart -and lose a raw material.The machine across the block.In the process of re -identifying the structure, the GT machine will have a delay in the determination of a structural block in other blocks.Therefore, although multi -square machines built across blocks can be used normally, when the block is re -loaded/uninstalled, there will be an incomplete structure.Please survey the boundary of the block before building a machine to avoid the error of "incomplete structure" due to cross -block.
Because each block will be loaded again when the server is restarted, this problem will become more serious.In particular, single -player games are essentially a local server.
4. The coil rewards of the blast furnace (only GT5.09)
In the unofficial GT5.09, GT has added several new coils, and some additional rewards are designed for these coils in the later versions.Here is a 5.09.29 mechanism.
These newly added coils have different basic thermal values -or furnace temperature.At least from GT4, the processing formula of the blast furnace has a demand for the furnace temperature. When the furnace temperature is not enough, many formulas cannot be processed.In addition, if the furnace temperature is higher than the temperature required by the formula, it will have some additional benefits to your processing: if the furnace temperature of the coil is 1800k required for the furnace required by the formula, it will provide an opportunity for a lossless overclocking;The furnace temperature required by the formula is 900K, and the energy consumed will be 0.95 on the basis of the previous basis; the two rewards will exist at the same time.
Take an example.Ultimet in GT, requires a furnace temperature of 2700K when burning, and processing 135s at 120EU/T power.Our blast furnace uses a 9001K furnace temperature silicone alloy coil and a LUV -level energy warehouse.It can be seen that the furnace temperature of the blast furnace is 6301K higher than the furnace temperature of the formula.After removing this number with 1800 and down to get 3, that is, there are 3 opportunities to have 3 non -destructive overclocking; except 900 and the whole is obtained by 7, that is, the power is reduced by 7 times.The power of the formula itself 120EU/T means that this is a MV -level formula, which is 4 levels lower than the LUV level of the blast furnace, with a total of 4 overclocking.According to the original overclocking rules, each overclocking power*4 is reduced by half, and the total power consumption is actually doubled; and 3 times without loss of overclocking means that the first three overclocking will be reduced to 1/4 (thereforeThe total energy consumption is unchanged, that is, "lossless"), only the fourth overclocking time is still halved according to the original rules, and the final time is 135s*(1/4)^3*(1/2) ≈ ≈1.06s, close to one piece per second; the power rises from 120EU/T for 4 times to 120EU/T*4^4 = 30720eu/t, and then calculate 7 power reductions. The final power is: 30720*0.95^7≈21453EU/T.
