This tutorial is set by the author's setting without permission.
[IC2] Reform version of biogas generator construction tutorial
Preface
When browsing the online biogas power generation tutorial, most of the criticisms were found: the work blocks are simple and humble, the power generation efficiency is not satisfactory, and sometimes even in short supply.So next I will talk about how to build an efficient marshmaqi motor.
Test: 500,000 EU bran, but a bran is durable ≈ 5 minutes in reality
Required materials
The square is left and right:
Flow heaters X6 Stelin generator X6 fermentation machine X3 solid heating machine X2 power heating machine X1 fluid/solid loader X1 MFSU power box X1 thermal generator X1 pump X1 funnel x4 steel storage box X1 X1 X1
Materials around
Bran X 起 (at least half of the group) Insulation Copper Circle X1 Copper Circle X2 tin wire x12 fluid pop -up upgrade X10 items to be upgraded to upgrade X1
The required materials are as above:
PS: The block in the article can be replaced by the bidding green characters.
sink
As shown in the figure, 3X3 unlimited water is changed as follows
Pump plugin.
The pump upgrade groove is placed in a streaming body to pop up and upgrade, and the pop -up direction is the top.
Ferry machine and flow/solid can
The three of the cans are placed in the canal upgrade slot. The fluids in the left, left, and right of the three directions pop up and upgrade. Two fluid pops up in the fermentor upgrade slot, respectively. The pop -up direction is detailed. See below.And the copper contact surface of the fermented machine must be in the direction of the firepower generator.
Plug -in pop -up and machine placement
The fermented fluid pops up to its front and left, or the right fluid heater.
Cable connection
The upper funnel is connected to the solid heating machine, and the omnidirection between the bottom of the solid heating machine below is the steel storage box
Plug -in direction
When putting a steel storage box, put the items into the canal upgrades into the upgrade in the canal in order to pump into the bran in the steel storage box.Put two fluids in the upgrade groove of the fermentation machine and pop up the upgrade. The pop -up direction is one side of the left and right.
Structure and tin line laying
The MFSU power storage box can be replaced with any IC power storage block equipment. The fluid heating machine of each two -layer structure is connected to the Sterling generator. Among the two -layer structure, there are four Sterling generators.Then laid tin wires.
Complete
There are two Sterling generators in the three -layer structure, which is a power heater in the middle. The power heater is recommended to plug in 2 coils to set up an aluminum line after laid the aluminum line to place two steel storage boxes above the funnel -—————The construction tutorial is over so far
After the machine is officially operated, remove the thermal generator, and the machine will supply power
Operating process
Power -powered pump pumping and providing cans → Infromaticing machine consumes bran and water to produce biomass → Automatic biomass liquid to fermentation machine
→ Ferment machine generates biogas to the solid heating machine → Automatic pop -up biogas liquid to fluid heater → fluid heating machine docking
Trin generator → The EU is continuously introduced through the cable through the heating biogas
Overclocking frequency
Efficiency adjustment: Because the three -layer architecture is a power heater in the middle, and can slightly increase or reduce power generation by changing the number of coils inside
The rate may also be insufficient due to overclocking.
Cost and fuel
Cost reduction: It is recommended to let the solid heating machine burn coal carbon.Consumption is not high
Questions sort out and answer
Question: Why use a solid heating machine and thermal generator?Didn't you say that you don't burn coal?
Answer: The overall architecture is collapsed with the power heating machine. The canned and pump does not supply the voltage.Power supply in the early stage of construction, remove after finishing.
Q: Can it be fully automatic?I put it in after braning.obedient!Come, let me bran!
Answer: External powder pour machine, insert items pop up and upgrade.They were squeezed, and they were so shy.
Question: Why didn't the fermenter react when working?The progress bar has not changed.
Answer: What the fermentation machine needs is thermal energy rather than electrical energy. The material of the copper contact of the fermented machine should be connected with the material of the heater.
Figures and archives
Because the text tutorial is limited, it is easy to understand the game archives.
Single storage file: biogas power generation archive code: FDZ1
